SYMplus™ CNC-software.

Methodical and proven

New features and optimizations –
all SYMplus™ Updates at a glance

SYMplus™ is regularly updated and improved

SYMplus™ with plusCARE™ is a living product. Every few weeks improvements, corrections, enhancements and brand new features are rolled out. The release notes provide an overview of all new features.

Information about the latest updates for SYMplus™ with plusCARE™: Always up-to-date here are the latest news

icon update blau weiß

Update 66 is now available. To learn how to install the update, click here:

  • General
    • 6741, 13206 Improved response to incompatible screen resolutions
    • 13026, 13281, 15032, 15042, 15237 Improvements in the free editor, display of special characters, especially concerning setup sheets
    • 14928 “Standard” as first option for saving the view in 3D simulation
    • 15135 Improved visualisation of small chamfers in 3D Simulation
  • PAL2020
    • 15098, 15098, 15168 e.a. Many improvements in the simulators. This applies in particular to the positioning paths in milling cycles, where the plunge point is approached directly instead of the setting point, and also to the cut-in cycles in turning.
    • 15052, 15115, 15254 Some bug fixes for rather unconventionally programmed lines and arcs in turning with driven tools (polar coordinates, opening angle, etc.)
    • 14941, 14949 New address “tenon height” in circular pocket and rectangular pocket
    • 10888 Oscillating plunge in rectangular pocket G72 and slot G74 is supported in the simulation
    • 15120 Improvements in the simulation for spiral clearing of a circular pocket
    • 15246 Changed address WV instead of W for tangential approach and departure
    • 15039 Position C axis for chord surface machining with G0 C/CI/CA (alternative to G15 G19 IP5 CM/CR)
    • 15151 G2/G3 with arc criterion (alternative to neg. R) as solution selection for the larger of the two possible arcs
    • 15057 Bug fixes in connection with the simulation of zero offsets with rotation (G59 WI/WA)
    • 15138 Zero offset with active G17 plane (end face) is supported
    • 15110 Incorrectly parameterized thread undercuts (G85 H1) are intercepted as far as possible during input.
    • 14931 Some programming errors in NC programs were only intercepted in the simulation or led to the simulation being aborted. An error message is now displayed in advance.
    • 15210 In the simulator for Turning with 2 axes, G18 can now also be programmed alone.
    • 15061, 15092, 15172, 15293 Minor improvements in some PAL help screens and texts
    • 14239, 15091 Further example programs adapted to PAL2020 (Attention: only applies to newly unpacked user data)
    • 15133 Integrated calculator can be used for gap-filling tasks
  • CAD/CAM
    • 15274 In turning, complete, closed contours can now also be imported from CAD (in front of and behind the turning center). SYMplus™ automatically takes over half of the contour; it is no longer necessary to trim on the axis or to take over half of the contour manually.
    • 10042 Cycle output for surface milling of “Circle” and “Rectangle” work steps (only applies to some controls, initially HAAS and SINUMERIK 810D/840D)
    • 15146 The “circle” work step can now also move in a spiral (as an alternative to “contour parallel”)
    • 15235 Improved calculation of an automatic plunge point for helix or ramp
    • 15301 There were occasional crashes when installing new tools directly in the work step. Bug fixed.
    • 15026 Changes to the parting off work step in turning were not applied. Error fixed.
    • 15187 Bugfix for deep hole drilling in turning
    • 9194, 10005, 11434 Improvements in the macro library and in the standard macro “Grooving” in turning
    • 15186 Bugfix when recalculating existing work steps
    • 15201 Icon renaming of blank and finished part molds and self-designed clamping devices: “File” instead of “Any”
  • Postprocessors
    • 11968, 12223, 15190 Generally improved handling of modalities by postprocessors, in some constellations, immersion feeds were not set or set incorrectly
    • 15191 NC blocks “at the end of the program” were under certain cirmumstances output after M30. Error fixed.
    • 14233, 14454 Improvements in FANUC21i-PP turning, e.g. gear steps are switchable
    • 13661 Bugfix in PP output from PAL for MAHO CNC432 (G43)
  • Simulators
    • 15262, 15283 Improvements to the simulation of POCKET3 and POCKET4 in the SINUMERIK 810D/840D simulator
    • 15075 Bugfix for the simulation of repeat loops in simulator HEIDENHAIN iTNC530
    • 15105 Angle ANG= on chord surface is supported in the 810D/840D simulator with driven tools now.
    • 14030 Scaling with G51 I J K in milling simulators FANUC 21i and 31i
    • 13961, 15179 Minor improvements/corrections in other simulators
  • 13488, 14402 Postprocessors HAAS and FANUC 0i/21 milling allow tool preselection.
  • 14653 Macro contours can be saved as part of the working plan
  • 14786, 14820, 14828, 14888, 14966 Text improvements in engl., chin. and ital. versions
  • 14873 Error correction concerning CYCLE81 read-in routine in 808D simulator
  • 14917 New sample program for PAL milling with swivel axes and corrections in other demo programs
  • 14925 Error in roughing algorithm with turning tool in 2nd quadrant fixed
  • 14946 14946 Milling cutter is no longer pre-positioned depending on the setting point for the PAL2020 rectangular pocket G72, but always in the pocket center
  • 14947 4-jaw chuck in 3D simulation
  • 14953 Wrong default setting regarding DIA/RAD/DRA in simulator PAL2020 C/Y with missing entry in the presetting file
  • 14983 Tool database turning for PAL exams Winter 2022 and Summer 2023 extended
  • 14989 Error when printing tool list fixed
  • 14999 Program header in postprocessor DECKEL dialog 11 can be switched off
  • 14860 Help screen for FL X/Y AN in HEIDENHAIN iTNC530 simulator
  • 14921, 14924 Errors in PAL help screens for G86/G88 corrected
  • 13692 Cycle call with G79 etc. did not consider the modality of a previously approached coordinate on chord surface (PAL2020 C/Y, G19 IP5). Fixed.
  • 14434, 14453 Positioning error after zero offset with rotation on face fixed in PAL2020 C/Y simulator
  • 14872 TR/TL was ignored in PAL2020 simulator milling if programmed in a separate block without T: Fixed
  • 14884 Dialog texts for plane selection in turning to PAL2020 C/Y improved
  • 14930 Z coordinates in G41 G45 etc. was interpreted incorrectly in PAL2020 Milling. Fixed.
  • 14933 Problems with polar programming on chordal plane (PAL2020 C/Y, G19 IP5) fixed.
  • 14934 Arcs with IA JA AO were simulated incorrectly on chord surface (PAL2020 C/Y, G19 IP5). Fixed.
  • 14940, 14952, 14987 Tenon in rectangular pocket after PAL2020.
  • 14954 Pendulum plunge into PAL rectangular pocket did not work with RN0. Fixed.
  • 14971 More flexible calculation of approach path when finishing rectangular and circular pockets according to PAL2020
  • 14984 Help texts for tool call according to PAL2020 adapted and supplemented.
  • 14997 G76 drilling distance on chord surface (PAL202 C/Y, G19 IP5) did not work correctly. Fixed.
  • 15029 Bug in G2/G3 dialog in “Basic Education 2020” mode (DIN Milling) fixed.
  • 15033 Bug in the simulation of TC0 (PAL2020 milling) fixed.
  • 14867 Bugfix regarding the selection of the machining strategy for roughing
  • 14275 The HEIDENHAIN iTNC530 simulator supports the programming of a straight line defined by angle and one end point coordinate
  • 14291 The SINUMERIK 810D/840D simulator supports the programming of circular arcs with center point and opening angle
  • 14764 Improved error handling in case of wrong plunge strategy in PAL pockets (rectangle, circle, groove)
  • 14837, 14839 Crash in case of incorrectly programmed retraction plane in PAL contour pocket is prevented
  • 13970,14504 Font size in the simulators scalable to 200
  • 14481,14617,14760 Login dialog for CmWAN licenses optimized (save password, reset)
  • 11485 Optimization of the work step Multi-pass Milling
  • 14512 Bugfix in update API
  • 14533 Buxfix colour table
  • 14647 Bugfix in 3D machine turning
  • 14680 One login ID can be used multiple times in the future (chargeable, on request)
  • 14762,14773 Bugfix UACEV2.DLL from TotalCmd installation
  • 14769 Buxfix CmWAN license
  • 14774 Bugfix Update-Manager error message
  • 14838 Optimization of the software start with not supported screen resolution
  • 14799 Software available in Italian language
  • 14693,9158,11317,11986,13029,14718, 14772, 14797 Improvements in the sources to work step macros
  • 13649 Teacher can predefine help texts for gap exercises/exams
  • 13703 Bugfix in postprocessor PAL -> HEIDENHAIN
  • 14393,14639 Text corrections in english version (PAL Multimedia)
  • 14455,14493 Bugfixes in work step “Finishing” and “Contour”
  • 14532 Tool positions in magazine/turret can be exchanged
  • 14640 Operating mode “Simulator” only visible if a simulator is also licensed
  • 14671,14672,14673,14674 Improvements in the FANUC postprocessor for driven tools (C axis)
  • 14679 Different allowance presets for roughing, facing, grooving
  • 14681 Syntax check for program name, simulator SINUMERIK 810D/840D
  • 14687,14709 Improvements in simulation of parting cycles G86/G88 according to PAL2020
  • 14688 Further sample programs according to PAL2020 coding
  • 14691,14692 Optimizations in work step “Recessing”
  • 14695, 14697 Plunging strategies according to PAL2020 for pockets and grooves revised
  • 14705 Bugfix in PAL2020 milling concerning TR, if programmed without T
  • 14708,14726 Bugfix at approach with G46 when working with a real Y-axis on face according to PAL2020
  • 12390,14725 Simulator 808D available
  • 11176,14736,14742 Support of label technique in CYCLE95 in SINUMERIK turning simulators
  • 14750 Bugfix in cycle POCKET3 of SINUMERIK milling simulators
  • 14755 Optimization in FANUC posts, output of technology data for each working step, even if they are unchanged
  • 14756 Improvement of the traverse path calculation (infeed paths) in the work step “Recessing”
  • 14777,14778,14780,14781,14782 Improvements in the HEIDENHAIN iTNC530 simulator regarding loops and parameter programming
  • 14377 In the HEIDENHAIN iTNC530 simulator, tools can now be called by their ID instead of T-number (selectable by fixed preset)
  • 14796 Output of an error message if the approach path leads to a collision when finishing the PAL contour pocket
  • 14809 Bugfix concerning behavior with underdetermined full circle with C-axis in turning
  • 14824 Stability improvement in the working plan
  • 14825 Help text for reclamping after PAL turning improved
  • 14827 Bugfix in simulation of tapping in simulator SINUMERIK 810/840D Milling
  • 14841,14238 Positioning in machine coordinate system with M91 is supported by HEIDENHAIN simulators.
  • 14811 Error in PAL help screen corrected
  • 13062 Simulation of different plunging strategies (helix, reciprocating) in SINUMERIK 810D/840D simulator
  • 14152 Simulator DECKEL Dialog 11 allows commands G60 and G64 for exact stop and looping respectively
  • 14754 Bugfix concerning trigonometric functions in simulator SINUMERIK 810D/840D turning
  • 14416 Bugfix concerning drilling depth in simulation in simulator FANUC 0i
  • 14505 In the HAAS simulator, transition elements can now also be programmed with ,C and ,R in Turning
  • 14606 Chamfering of pockets according to PAL2020 with QM-1
  • 14609,1461 Parameterization in G58 and G59 zero offset according to PAL2020 changed (Milling and Turning)
  • 14650 Diameter or radius programming in block G15 G18 according to PAL2020 switchable with DIA/RAD/DRA
  • 14677,14678,14689 Behaviour when reading old PAL programs in PAL2020 simulator improved
  • 14686 Simulation of G86/G88 regarding safety distance improved
  • 14810 Wrong sorting of commands G40 G45ff. in listbox (Turning with C-axis) corrected
  • 13970,14504 Font size in the simulators scalable to 200
  • 14481,14617,14760 Login dialog for CmWAN licenses optimized (save password, reset)
  • 11485 Optimization of the work step Multi-pass Milling
  • 14512 Bugfix in update API
  • 14533 Buxfix colour table
  • 14647 Bugfix in 3D machine turning
  • 14680 One login ID can be used multiple times in the future (chargeable, on request)
  • 14762,14773 Bugfix UACEV2.DLL from TotalCmd installation
  • 14769 Buxfix CmWAN license
  • 14774 Bugfix Update-Manager error message
  • 14838 Optimization of the software start with not supported screen resolution
  • 14799 Software available in Italian language
  • 14693,9158,11317,11986,13029,14718, 14772, 14797 Improvements in the sources to work step macros
  • 13649 Teacher can predefine help texts for gap exercises/exams
  • 13703 Bugfix in postprocessor PAL -> HEIDENHAIN
  • 14393,14639 Text corrections in english version (PAL Multimedia)
  • 14455,14493 Bugfixes in work step “Finishing” and “Contour”
  • 14532 Tool positions in magazine/turret can be exchanged
  • 14640 Operating mode “Simulator” only visible if a simulator is also licensed
  • 14671,14672,14673,14674 Improvements in the FANUC postprocessor for driven tools (C axis)
  • 14679 Different allowance presets for roughing, facing, grooving
  • 14681 Syntax check for program name, simulator SINUMERIK 810D/840D
  • 14687,14709 Improvements in simulation of parting cycles G86/G88 according to PAL2020
  • 14688 Further sample programs according to PAL2020 coding
  • 14691,14692 Optimizations in work step “Recessing”
  • 14695, 14697 Plunging strategies according to PAL2020 for pockets and grooves revised
  • 14705 Bugfix in PAL2020 milling concerning TR, if programmed without T
  • 14708,14726 Bugfix at approach with G46 when working with a real Y-axis on face according to PAL2020
  • 12390,14725 Simulator 808D available
  • 11176,14736,14742 Support of label technique in CYCLE95 in SINUMERIK turning simulators
  • 14750 Bugfix in cycle POCKET3 of SINUMERIK milling simulators
  • 14755 Optimization in FANUC posts, output of technology data for each working step, even if they are unchanged
  • 14756 Improvement of the traverse path calculation (infeed paths) in the work step “Recessing”
  • 14777,14778,14780,14781,14782 Improvements in the HEIDENHAIN iTNC530 simulator regarding loops and parameter programming
  • 14377 In the HEIDENHAIN iTNC530 simulator, tools can now be called by their ID instead of T-number (selectable by fixed preset)
  • 14796 Output of an error message if the approach path leads to a collision when finishing the PAL contour pocket
  • 14809 Bugfix concerning behavior with underdetermined full circle with C-axis in turning
  • 14824 Stability improvement in the working plan
  • 14825 Help text for reclamping after PAL turning improved
  • 14827 Bugfix in simulation of tapping in simulator SINUMERIK 810/840D Milling
  • 14841,14238 Positioning in machine coordinate system with M91 is supported by HEIDENHAIN simulators.
  • 14811 Error in PAL help screen corrected
  • 13062 Simulation of different plunging strategies (helix, reciprocating) in SINUMERIK 810D/840D simulator
  • 14152 Simulator DECKEL Dialog 11 allows commands G60 and G64 for exact stop and looping respectively
  • 14754 Bugfix concerning trigonometric functions in simulator SINUMERIK 810D/840D turning
  • 14416 Bugfix concerning drilling depth in simulation in simulator FANUC 0i
  • 14505 In the HAAS simulator, transition elements can now also be programmed with ,C and ,R in Turning
  • 14606 Chamfering of pockets according to PAL2020 with QM-1
  • 14609,1461 Parameterization in G58 and G59 zero offset according to PAL2020 changed (Milling and Turning)
  • 14650 Diameter or radius programming in block G15 G18 according to PAL2020 switchable with DIA/RAD/DRA
  • 14677,14678,14689 Behaviour when reading old PAL programs in PAL2020 simulator improved
  • 14686 Simulation of G86/G88 regarding safety distance improved
  • 14810 Wrong sorting of commands G40 G45ff. in listbox (Turning with C-axis) corrected
  • 14664, 14666 Important bug fixes regarding the output of tool correction memory numbers
  • 14660 et seq. Bug fixes in the DIN/PAL simulators
  • 9171 Max. speed can be set in the turning work plan
  • 14457 Individual speed limitation can be set for each work step
  • 14510 Simulation of the milling cutter correction for the DECKEL simulator
  • 14511 Correction memory number can be preset in the turret/magazine
  • 14513 DECKEL-PP Dialog11 translates TR/TL to G49/G48
  • 14515 Correction in Dialog11 help picture for G48/G49
  • 14518 Grooving cycles G86 and G88 according to PAL2008 work again
  • 14546 Bugfixing the PP run
  • 14554 Optimization of the preset drilling depth in the turning work plan
  • 14559 G94 was not interpreted in SIEMENS simulators. Fixed.
  • 14563 Added help texts for POCKET3 and POCKET4 in SIEMENS simulators
  • 14567 Pendulum immersion in POCKET4 in SIEMENS simulator was missing. Fixed.
  • 14572 Fixed a bug in axial grooving regarding max. cutting depth
  • 14585 CmWAN access data can be saved on a local computer
  • 14587 CmWAN login dialog without license activation
  • 14591 Clamping devices preset when importing a G1/G2/G3 contour (turning).
  • 14595 Workaround to avoid problems when creating a finishing path via ini entry
  • 14603 G78 can be selected as a cycle for thread cutting in the PP FANUC 21i
  • 14605 Extension of macro programming to allow contour loading
  • 14628 Fixed problem with PAL facing cycle after reclamping
  • 14507 Changed tool call for PAL2020 in milling
  • 14508 No more positioning logic in G0 traversing blocks acc. to PAL2020 milling
  • 14519 PAL2020 is now the default mode after reinstallation
  • 14521 Plane swivel according to PAL2020 milling with G15 instead of G17
  • 14530, 14568 Plane selection with G15 IPx acc. to PAL2020, turning with driven tools
  • 14547 Addresses RG and LG added to G88 dialog
  • 14574 Tool width equal groove width did not work. Fixed
  • 14618; 14645 New sample programs acc. to PAL2020 (only for new installations)
  • 14626, 14627 Gap tasks improved and new for PAL 2020 (only for new installations)
  • 13965 Fixing a display problem at 1366×768 Pixel Screen Resolution
  • 14262 Improve connection stability for CmWAN licenses.
  • 14396 Recommended procedure for problems with the display of the Virtual Workshop
  • 14479 Improvement of traverse paths when milling a sphere
  • 12010 Use of rotary drills in the Workplan is possible (“EcoCut” tool)
  • 12948 Manufacturing by means of iterated lateral infeed in the Milling Workplan 
  • 13268, 13269, 13385, 14405 Improvements and enhancements in postprocessor output
  • 13901 Improved handling in the Workplan
  • 14044 Approach and departure in a semicircle during contour milling
  • 14376, 14156, 14219, 14444, 14446, 14480, 14471 Improvements in the various simulators
  • 14330, 14384, 13371, 14426 Improvements in the PAL simulators
  • 14397 Fixed various issues in the Workplan.
  • 14434, 14390, 14368, 14369, 14379 Improvements and enhancements in PAL2020
  • 14373, 14374 Error when creating finishing paths “from left to right” (e.g. inside, on the left flank of recesses, flat surfaces, …) fixed
  • 14336, 14337 Error when programming with Q parameters corrected in the simulator HEIDENHAIN iTNC530 Dialog
  • 14338 Improvement in CYCL209 in the simulator HEIDENHAIN iTNC530 Dialog
  • 14341 In the simulators for PAL2020 you can now define arcs with I / J and AO.
  • 14358 Change to the work step name is recorded as a work plan change (*)
  • 14366 PAL sample program with Y-axis prepared in conformity with PAL2020 (new groove cycle)
  • 14170, 14173: Additional PAL simulators based on the new PAL specifications 2020. 
    • New behavior regarding the approach and departure paths for tool radius compensation for Milling and for driven tools in Turning
    • Modified and additional settings for radial and axial cut-in cycles G86, G88
  • 14257: problems with 3D simulation in Turning in connection with INTEL UHD graphics cards fixed
  • 10913: Extended support in the choice of approach and departure points for finishing e.g. of rectangular pockets and grooves in Milling
  • 13685: Export of a Milling geometry data in STL format
  • 13885: New setting for the milling work plan so that rapid traverse paths can be calculated and simulated interpolated or non-interpolated
  • 14003: In the PAL simulator Turning with the C/Y, the reference point EP for the rectangular pocket G72 in G19 was interpreted incorrectly. Fixed.
  • 14144: Range of values for radii increased in the operating mode Geometry
  • 14148: Crash in PAL simulator Turning with C/Y in connection with G17 Y and G19 Y fixed.
  • 14150: Improvement of the value transfer from the calculator in the operating mode Geometry
  • 14159: Improved feed output in the Fanuc postprocessors forTurning
  • 14160, 14189: Improvement of the travel paths in Turning work plan when finishing with a grooving tool
  • 14171: Improvement in Turning postprocessor Fanuc 21i Turning regarding G32/G33
  • 14172: Improvement in Turning work plan regarding negative allowances in X and Z.
  • 14182, 14185: Improvements in the HAAS simulator turning with C-axis
  • 14197: Postprocessor Deckel Dialog 11: Extension of the parameter set 
  • 14208: Workplan Turning: Improved the display of the “red areas”
  • 14220, 14227: Minor bug fixes in simulators 
  • 14223: Simulator Siemens Milling: Improved when translating a Siemens 840D program into Heidenhain format
  • 14299: Simulation now responds to a “conditional stop” (M1)
  • 14235: PAL Simulator Turning and Milling: The setting regarding the program check is saved.
  • 14265: Operating mode Teacher: Pre-setting for “Submitting examination” changed to “Central”
  • 14284: Improvement of the program output in postprocessor NUM 1060T
  • 14289: Improvement in PAL simulator with 3+2 axes: Rapid traverse paths were simulated in feed after G17. Fixed.
  • 14290: Wrong modality in PAL simulator Milling when changing from G94 to G95 fixed.
  • 14297: New cycles in Heidenhain simulator iTNC530 DIN: G220 and G221 added.
  • 14308: In work plan Milling, the maximum number of cuts when manufacturing a chamfer with a spherical cutter line by line increased
  • 14311,14200: Extension of the tool databases with a rear face cutter (Turning) and a radius cutter (Milling)
  • 14326, 14329: Improvements in the PAL simulator with C axis regarding G17C
    14221: New demo programs for some common milling simulators added
  • 14145: Improvement in the Czech language version
  • 11888 Milling on the front face with real Y-axis (G17 Y) completed in simulator PAL C/Y
  • 13113, Fillet (alternative to chamfer, rounding) with ball cutter
  • 13966 Lines now also possible with several lateral infeeds
  • 13030, 14125 Copying of macro working steps, clamping and handwheel enabled
  • 13940 Thread travel with inlet and outlet again as one NC block (instead of three)
  • 13977 PAL arc grooves on face now also programmable with G75 EP0 and G77 R0
  • 14055 Feed factor FRF will be set as mandatory for PP output for SINUMERIK 840D
  • 14058 PP output of PAL Snnnn M13 as M3 and M8 always in two lines
  • 14063 Contour violation in simulation with PP translation from PAL G41 G45 fixed
  • 14064 Cycles from G230 onward added to the HEIDENHAIN iTNC530 DIN simulator
  • 14067 Swedish language installation files available
  • 14070 Installation files available in Romanian language
  • 14085 Improvement in cutting-off operation
  • 14086 Improvement for machining with V-chisel
  • 14095 Chisel did not finish a section, which is shorter than it is wide. Fixed.
  • 14096 PP output for reclamping (milling) improved
  • 14099 PP output for GSK 988T matched with simulator GSK 988T
  • 14101 PP error regarding CYCLE83 (turning) for SINUMERIK 802D fixed
  • 14118 With PP output from PAL the starting point of the simulation is no longer approached
  • 14119 In case of PP output from PAL with program end character, M30 was output afterwards. Fixed.
  • 14117 Optimized retraction path during internal turning
  • 14083, 14088 Example work plans turning updated
  • 14069, 14091, 14132 Tool databases milling/turning extended by some tools
  • 14133 Sample routings specifically for PP tests added
  • Spanish language installation files available
  • Installation files available in Czech language
  • Installation files available in Danish language
  • 14016 Simultaneous start of SYMplus™ turning and milling enabled
  • 13984 New shortcuts +/- (instead of Alt+PgUp/PgDown) for handwheel positioning
  • 13981 3D-View in the routing basic menu milling works again
  • 14022 Interpreter in the HEIDENHAIN iTNC530 simulator Improved dialog for arithmetic operations
  • 14021 Missing arithmetic function FBD added in FANUC simulators
  • 14017 Block numbers for FANUC simulators (milling) no longer mandatory
  • 14027 Scale change G51 in FANUC simulators (milling)
  • 14028 End-of-line comments allowed in FANUC simulators (milling)
  • 14033 New FANUC sample programs (milling)
  • 14050 Missing help texts in simulator FANUC 18i C added (rotate)
  • 13996, 13997 Current versions of Notepad++ and TotalCommander integrated
  • 8851 The design of a V-chisel improved
  • 13548, 13550, 13945 Coolant commands for transmission ratio from PAL Turning incorrectly set. Fixed.
  • 13856 New PAL sample program Turning with Y axis
  • 13857 New PAL sample program Milling with relative tilt and different milling speeds swivel behaviour
  • 13898 45° rapid traverse non-interpolated simulation in other FANUC simulators
  • 13900, 13947 Improvements in the Update Manager
  • 13927 Automatic switching FRK CAM/control corrected
  • 13932 Bug in dialog of Heidenhain simulators when changing X/XI etc. fixed
  • 13933 Error in output of helix and pendulum movements fixed
  • 13936 Sorting of names in the student list (operation mode teacher) improved (umlauts, special characters)
  • 13937 Error during mirroring (with M84) in DECKEL simulator fixed
  • 13939 Correction memory TC(n) in SINUMERIK Simulator 840D sl/828D switchable in a separate line
  • 13941 Error in roughness depth display fixed
  • 13942 Error in machining cycle G81 in simulator GILDEMEISTER EPL1 corrected
  • 13944 Stability improvement in the handling of defective work plan files
  • 13946 Stability improvement for turret change in existing work plan
  • 13950 French multimedia module activated in the HEIDENHAIN iTNC530 simulator
  • 13951 HAAS post processors switchable between G00, G01 etc. and G0, G1 etc.
  • 13952 HAAS simulators switchable between G00, G01 and G0, G1
  • 13954 Dimensional fit calculator, input also for “decimal numbers
  • 13955 Parameter programming also in PAL simulator Turning with 2 axes
  • 13958 Format check for program name for installation in HAAS-Simulator
  • 13960 HEIDENHAIN Simulator now accepts spaces in file name
  • 13968 Waiting bar during unpacking the DATADIR.ZIP
  • 12833 Reloading modified precast element into the work plan simplified
  • 13867 Contour train programming after PAL milling (G61 ff.) improved
  • 13864, 13865, 13875 Stability behaviour in work plan mode improved
  • 13886 FANUC-Simulators 0i and 18i (G-Code System A) Rotation simulate rapid traverse paths now non-interpolated, switchable)
  • 13895 FANUC postprocessors 0i and 18i turning generate rapid traverse paths parallel to the axis by default
  • 13887 Postprocessors can (switchable) output block numbers only in connection with a tool call or speed change
  • 13888, 13902 SINUMERIK postprocessor 840D sl / 828D and 808D turning can output tool call and cutting data in separate lines
  • 13797 Post processor HELLER Unipro, cycle output improved
  • 13861 Error in blank model after reclamping fixed
  • 13889 DIAM90 is available again in 810D/840D and 802D turning simulators
  • 13892, 13893 Error at helical and oscillating immersion fixed
  • 13800 PP error at conversion of PAL departure path fixed
  • 13822 Radius correction is automatically switched to CAM when milling with a radius cutter
  • 13862 Text corrections Chinese
  • 13890 Text corrections English
  • 13872 Dialog for G2/G3 expanded in the HEIDENHAIN iTNC530 DIN simulator
  • 13821 New “Stud” machining strategy for surface milling
  • 13660 General view for large, ring-shaped workpieces improved for practical use (turning)
  • 13652, 13653 G51 instead of G59 (NPV incremental instead of absolute) in DINplus post processor and simulator
  • 13467 PP-error in the gear ratio of M13 (direction of rotation + coolant) corrected
  • 13398, 13811 Simulator SINUMERIK 810D/840D did not support long file names. Fixed.
  • 13730 Switch for separate output of tool call and cutting data for FANUC-PP 0T and 0i (turning)
  • 13793 Error in the groove step corrected
  • 13794 Error in roughness display fixed
  • 13798 PAL pocket cycles now consider plunging feed rate
  • 13799 Improvement in PAL circular pocket cycle with trunnion
  • 13823 Improvement in Hurco post-processor (milling)
  • 13820 Error regarding approach and departure paths during alternating line balancing fixed
  • 13825 Corrected error when trimming chamfers with ball nose cutter
  • 13835 New sample work plan for tenoning and trimming
  • 13812, 13813, 13817, 13818, 13827, 13826 Various improvements in non-German versions (especially Chinese)
  • 13840 Backup of the temp. work plan in case of crash/power failure works again
  • 12892, 13582, 13775, 13780 Improvements in the update manager
  • 13689, 13747 Display of the theoretical roughness depth for each element of a turning contour in the work plan and in the simulators
  • 13741 Undo (Ctrl+Z) and Redo (Ctrl+W) now also in PAL Simulator and Control Simulators
  • 13702 Plunge on a ramp in PAL groove cycle G74 implemented
  • 13706, 13720, 13706, 13720 Error corrections to Ctrl+Z/Ctrl+W in geometry and work plan
  • 13753 Switch in HURCO-PP for alternative tool call via tool name (T-ID) instead of station number
  • 13771 New option when filleting (chamfer, rounding): in synchronous/counter-clockwise rotation alternating
  • 13540, 13575 Virtual Workshop now works on Terminal Server or Citrix Client
  • 13734, 13735, 13736 Text corrections in all non-German language versions
  • 13766 Extensive revision of the software texts in the Chinese version
  • 13742 Name conflict in 810D/840D simulators between UP names and function names (SIN, TAN, …) fixed
  • 13746 Changeover to TeamViewer 13 (for remote maintenance)
  • 13762 Wrong finishing path proposal after reclamping (work plan turning) corrected
  • 13770 Fixed wrong plunge angle when finishing in the third quadrant
  • 13728 “Finishing only margin” with H4 in the help texts of the PAL simulators
  • 13696 Help for PLANE RESET in Heidenhain iTNC530 simulator improved
  • 13110 Presets for PP SINUMERIK 840D sl / 828D milling improved
  • 13711, 13713, 13715 Occasional crashes when opening/saving work plans
  • 13713 3D simulation in simulators with blank description disabled in program
  • 12752, 13184 Undo (Ctrl+Z) and redo (Ctrl+W) when creating workpiece geometries and work plans
  • 13686 Standard tool database in turning extended
  • 13523 Title bar adapted for full screen mode
  • 13651 Stitching algorithm with depth division improved
  • 13670, 13671 Improvements in the update manager
  • 13647 Postprocessor supports part catcher with dwell time during cut-off (turning)
  • 13654 Postprocessor supports high pressure pump with dwell time (turning)
  • 11803, 13656 Improved positioning paths for controls switchable without rapid traverse interpolation (turning)
  • 12979 Error in coordinate system rotation with P parameter fixed (PAL milling)
  • 13645 Error in axial grooving with G88 fixed (PAL turning)
  • 13657 Harmonisation of simulator and post-processor with regard to tapping G36 (DINPLUS simulator)
  • 13668 Switching on the radius correction by MAHO-PPs as standard with G43
  • 13674, 13452, 13518, 13648 Translation corrections
  • 13675 Gap test TEST3 in milling revised
  • 13691 Error concerning element selection after area delimitation in CAD module fixed
  • 10814, 10815 Error in simulation of pocket cycles G72 and G76 fixed (cover dialog 4)
  • 11631 Error in simulation of the swivel command PLANE PROJECTED corrected (Heidenhain TNC530)
  • 11809 Error in simulation of Cycle 211 Round Slot corrected (Heidenhain TNC530)
  • 13665 Graphics card conflicts under Windows 10 in multimedia modules (PAL, FANUC, HAAS, HEIDENHAIN) fixed
  • 13642 Improved license display, new product design
  • 13648 Improved English translation of Fanuc simulators
  • 13658 PP error during tapping corrected
  • 13632 Corrected text error in Chinese version
  • 13659 Textual errors in French version corrected
  • 13599 Help texts for parameter programming translated
  • 13662 Improvements in the update manager
  • 13643 Simplified extension of the plusCARE™ maintenance interval
  • 6810 Parameter Programming for HEIDENHAIN TNC430 (Milling)
  • 9386 Parameter programming for HEIDENHAIN iTNC530 (milling)
  • 7959 Parameter programming for SINUMERIK 810D/840D (turning and milling)
  • 12178 Parameter programming for FANUC 0i/18i and GSK (turning and milling)
  • n.n. Parameter programming for HAAS (turning and milling)
  • n.n. Parameter programming for PAL (turning and milling)
  • 13615 New sample programs with parameters (turning and milling)
  • 12843 Alternative solutions in gap checks (e.g. M3 and M13, AS-90 and AS270)
  • 12853 Text corrections in Russian version
  • 13566 Conflict in bore selection (single bores, 180° arcs) fixed (milling work plan)
  • 13583ff. Various improvements in the Update Manager
  • 13590 Special postprocessor error fixed
  • 13604 Text corrections in English version
  • 13606 G43 and G41/G442 deleted from G2/G3 dialogue (FANUC simulators)
  • 10270 DIAMON/DIAMOF/DIAM90 switch in sinumeric simulators
  • 13549, 13552 Error corrections in the update manager
  • 13557 Improvements in the use of CmWAN licenses
  • 13428 Improvements when approaching the tool change point “only in Z
  • 13553 Error correction in the Okuma post processor regarding threading
  • 12421 G0 no longer allowed when G12.1 is active in FANUC simulators with C axis
  • 12096, 12711, 12842, 13046, 13107, 13109, 13119, 13132, 13274 Text corrections in multimedia modules DIN, PAL, HAAS
  • 13554 Too restrictive speed limit at G94 in simulators with started tools fixed
  • 13560 new WiBU Runtime integrated
  • 13561 TeamViewer version 12 integrated
  • 13563 Improvement in 2D simulation with too small working space
  • 13551 New DXF examples added
  • 13533 Portuguese language installation available
  • 13510 Bends in the precast element with opening angle ≥ 180° can now also be selected as drilling positions (e.g. exposed corners of a rectangular pocket)
  • 11162 Postprocessor handling of Unicode characters in comment lines for NC program
  • 13527 Error concerning left-hand thread in SIEMENS simulators fixed
  • 12525 Comment line in header line allowed in FANUC0i simulator
  • 11588 In the selection list of commands/cycles of the control simulators, the meaning of the G-functions is now also displayed in plain text (as before in the PAL simulator) in addition to the G-functions. This gives the newcomer a much better orientation.
  • 10660, 12999 “Reset” button in the simulation graphic for a quick restart without leaving the graphic
  • 13438 “Complete” selection for common start of operating modes from DIN/PAL, control, CAD/CAM available again
  • 13514 “Smoother” simulation of the swivel movement in the 3D simulation with 3+2 axes
  • 13498 Simplified use of SYMplus by several independent users on one PC
  • 12435 More specific error message in PAL simulator Turning with C/Y
  • 12819 PAL roughing cycle algorithm improved
  • 12822, 12851 Error in PAL auxiliary images rotation corrected
  • 11617, 12603, 12632, 12792, 12901 Improvements/troubleshooting in simulators for FANUC turning, FANUC milling with swivel, HAAS, HEIDENHAIN, SIEMENS 840D milling
  • 13478 New sample work plan with trochoidal milling
  • 13508 Error in slot milling corrected
  • 12091 With the setting “Full Screen” Windows task bar is taken into account
  • 3928, 4819, 7144, 8889, 9135 Expansion in the parting step: Cutting off not necessarily until “falling down
  • 7606, 10041, 12107 New cycle in the HAAS milling simulator: pocket milling cycle G150 (contour pocket)
  • 13426 Expansion in work step: Slot milling: Trochoidal milling (whirl milling) as a new machining strategy
  • 13434 Extension in geometry: Narrow variant of the DIN font
  • 13464 Improvement in KNUTH post processor GPlus 450
  • 13383, 13165 Improvement in the graphics and information texts
  • 13411 Speed limits in PAL simulator changed
  • 13453 Improvement of the French translation
  • 13485 Improvement of the Dutch translation
  • 13398 Correction of minor graphical errors (icon frame)
  • 13425 Adoption of further postprocessors into the “complete package” (in SYMplus plusCARE™ these are thus available to all users!)
  • 13422 Correction of an error in surface milling with small contact widths
  • 13443 Work steps can be named individually
  • 13445 Linking the user data via environment variable
  • 12953 Selection of similar holes (same diameter) when transferring from CAD files
  • 13059 Postprocessors PAL 3+2 -> SINUMERIK 840Dsl/828D and HEIDENHAIN TNC620 available
  • 13407 Algorithm optimization for handling numerical problems in the work plan
  •  13217 Improvements in licence management
  • General New interface design New installation via msi (Microsoft Installer) Standard user data is provided as a ZIP file for restores
  • PAL 
  • 11677 Tool fine compensation TR/TL for driven tools in turning added (C axis)
    12771, 13153, 13155 Behavior during pocket milling with respect to parameter H (roughing/finishing) changed, consideration of TR when chamfering pocket cycles (turning and milling)
  • 12683 Angle <> 0° from G79 affected the following contour pocket G34ff. Fixed.
  • 12699 Instruction list in G1/G2/G3 now also with explanatory terms like in PAL simulator
  • 12862, 12942 Corrections in PAL-Multimedia (Rotation)
  • 12160 Start wizard in PAL-Simulator switches to simulation settings also when importing G1/G2/G3 contours
  • 13220 Reorganization of the contents of the PAL simulators (“mode”): basic education (as before), PAL (corresponds to “further education” mode), PAL 3+2 or PAL C/Y (corresponds to PAL 2012). Mode PAL2009 not applicable
  • 13312 If licensed, the mode with additional axes (PAL 3+2 or PAL C/Y) is now always active after installation
  • Simulators
  • 13278 Error in HEIDENHAIN simulators regarding M3 in cycle call corrected
  • 13293 Error in Simulator DECKEL Dialog 4 regarding feed/ plunge feed corrected
  • Work plan 
  • 12873 Approach length 0 led to error message during PP run Fixed.
  • 13114 Work step Surface does not find pilot hole. Solved.
  • 13142 Protection zone outside prevents splashing. Solved.
  • 13301, 13303 Presettings without blank and in milling without clamping devices, blank rectangle or cylinder then automatically adapts to the dimensions of the finished part.
  • PPs  
  • 13262 Postprocessor SINUMERIK 840D sl / 828D optimized for DMG machines
  • 13352 HEIDENHAIN TNC620 Postprocessor added to the HEIDENHAIN PP family
  • 13353 Tool preselection switch added to PPs iTNC530 and TNC620
  • 13284 Postprocessor for KNUTH control GPlus 450 available
  • 12862 Error in Heidenhain PPs fixed

New here? Then become a part of the KELLER family now.

Contact

Our experts are at your disposal. We look forward to your inquiry!

Jürgen Mues

    Mr.Ms.
    Details about your company / school
    Details for your personal offer
    How many users should work simultaneously with SYMplus™?
    For which technologies do you need SYMplus™?
    Which modules of SYMplus™ interest you?
    SYMplus Turning
    SYMplus Milling